R-pod Owners Forum Homepage

This site is free to use.
Donations benefit a non-profit Girls Softball organization

Forum Home Forum Home > R-pod Discussion Forums > Podmods, Maintenance, Tips and Tricks
  New Posts New Posts RSS Feed: older post on adding window to RPod Door?
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

Topic Closedolder post on adding window to RPod Door?

 Post Reply Post Reply Page  <12
Author
Message
Ben Herman View Drop Down
Senior Member
Senior Member


Joined: 26 Apr 2018
Location: Gr Junction, CO
Online Status: Offline
Posts: 354
Direct Link To This Post Topic: older post on adding window to RPod Door?
    Posted: 20 Mar 2019 at 7:38pm
Originally posted by voisj

I have a few pictures of my window. I cut the opening with a jigsaw after drilling a pilot hole. I used the stiffest blade I could find so it would cut without deflecting.
Pretty much was just;
mark the hole,
cut the hole,
apply silicone,
insert window,
screw on interior trim ring,


Nice job! I'm sure it will go fine, just didn't want to reinvent the wheel and surprisingly an Amazon search wasn't bringing up the Vintage Technologies window, so am glad that StephenH posted. 
Back to Top
Ben Herman View Drop Down
Senior Member
Senior Member


Joined: 26 Apr 2018
Location: Gr Junction, CO
Online Status: Offline
Posts: 354
Direct Link To This Post Posted: 20 Mar 2019 at 7:40pm
Originally posted by voisj

I have a few pictures of my window. I cut the opening with a jigsaw after drilling a pilot hole. I used the stiffest blade I could find so it would cut without deflecting.
Pretty much was just;
mark the hole,
cut the hole,
apply silicone,
insert window,
screw on interior trim ring,


voisj looks like you cut your window without removing the door? I was thinking that it would be easier to remove the door to be able to make the cut in a horizontal position (door on sawhorses). Did you have any difficulties cutting the door in place?
Back to Top
voisj View Drop Down
Senior Member
Senior Member
Avatar

Joined: 19 Jul 2016
Location: San Luis Obispo
Online Status: Offline
Posts: 471
Direct Link To This Post Posted: 20 Mar 2019 at 8:14pm
Ben,
I did it in place because I didn't want to remove the door, It works and was aligned perfect, and you know Murphys law.
The main issue was styrofoam particals EVERYWHERE. I put a sheet over the screen door and shut it so the inside stayed clean.
I had to make a temp brace so the door wouldn't swing while I cut and used blue tape to make sure it didn't sag while the silicone dried.
I opted for the window with the pull down blackout shade, takeoff on Ebay $56. Not sure about operable windows.
Don't be to scared,it's not that big of a job, measure 3 times cut once, Good luck!!
John
SLOPODMODS
John&Sue,SLO,CA
2016 180 HRE, 2013 F150 Eco Boost
 
Back to Top
Pod People View Drop Down
Senior Member
Senior Member


Joined: 22 Sep 2011
Location: Chapel Hill,NC
Online Status: Offline
Posts: 1065
Direct Link To This Post Posted: 21 Mar 2019 at 8:17am
It’s pretty easy to remove the door-just several screws on the hinges. I think it makes the job a lot easier to put the door on padded saw horsesvann

Vann & Laura 2015 RPod 179
Back to Top
foadman View Drop Down
Newbie
Newbie


Joined: 10 Sep 2015
Location: Elmira, NY
Online Status: Offline
Posts: 28
Direct Link To This Post Posted: 23 Mar 2019 at 9:21am
I have an R Pod171 which has a window next to the door so I am thinking about installing a peep hole in lieu of a window. Can you think of any issues? Looks like there are not any structural members in the middle of the door? Peep hole minimum thickness is 1-3/8 inch, is the center section of the door less than that? Appreciate you thoughts!
bmiller
Back to Top
foadman View Drop Down
Newbie
Newbie


Joined: 10 Sep 2015
Location: Elmira, NY
Online Status: Offline
Posts: 28
Direct Link To This Post Posted: 23 Mar 2019 at 9:22am
I have an R Pod171 which has a window next to the door so I am thinking about installing a peep hole in lieu of a window. Can you think of any issues? Looks like there are not any structural members in the middle of the door? Peep hole minimum thickness is 1-3/8 inch, is the center section of the door less than that? Appreciate you thoughts!
bmiller
Back to Top
Ben Herman View Drop Down
Senior Member
Senior Member


Joined: 26 Apr 2018
Location: Gr Junction, CO
Online Status: Offline
Posts: 354
Direct Link To This Post Posted: 23 Mar 2019 at 10:10am
Originally posted by foadman

I have an R Pod171 which has a window next to the door so I am thinking about installing a peep hole in lieu of a window. Can you think of any issues? Looks like there are not any structural members in the middle of the door? Peep hole minimum thickness is 1-3/8 inch, is the center section of the door less than that? Appreciate you thoughts!

Door thickness is 1.5" - as long as the peephole is adjustable should be fine. What I can gather from other posters is that the door center is just foam, no structural members in there. Just ordered my door window, will post photos of the install once it arrives next week.
Back to Top
foadman View Drop Down
Newbie
Newbie


Joined: 10 Sep 2015
Location: Elmira, NY
Online Status: Offline
Posts: 28
Direct Link To This Post Posted: 23 Mar 2019 at 12:36pm
Thanks!
bmiller
Back to Top
Pod People View Drop Down
Senior Member
Senior Member


Joined: 22 Sep 2011
Location: Chapel Hill,NC
Online Status: Offline
Posts: 1065
Direct Link To This Post Posted: 23 Mar 2019 at 9:38pm
You are correct-there is nothing in the door except the inner/outer skin and foam interior. Tape both sides, trace and cut away. Clean the surfaces with ed alcohol before using silicone caulk so that it will stick better.
Vann

Vann & Laura 2015 RPod 179
Back to Top
 Post Reply Post Reply Page  <12

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.64
Copyright ©2001-2009 Web Wiz