R-pod Owners Forum Homepage

This site is free to use.
Donations benefit a non-profit Girls Softball organization

Forum Home Forum Home > R-pod Discussion Forums > Podmods, Maintenance, Tips and Tricks
  New Posts New Posts RSS Feed: $30 Lift Kit
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

Topic Closed$30 Lift Kit
 Post Reply Post Reply Page  12>
Author
Message
  Share Topic Share Topic  Topic Search Topic Search  Topic Options Topic Options
NXRocks View Drop Down
Newbie
Newbie
Avatar

Joined: 27 Apr 2014
Location: Evergreen, CO
Online Status: Offline
Posts: 24 		Direct Link To This Post Topic: $30 Lift Kit
    Posted: 19 May 2014 at 11:19pm
2x4x3/16" - 12" - $10 (per side)
Hardware - $10
4 holes to drill (per side)
Total time - 2 hrs

If you are just a bit handy - you'll figure this out. It is stronger, better and will cost you a lot cheaper than the outrageously expensive one going around for as much as $200

I did weld the corners - just because I'm crazy and I overbuild everything - but is not necessary. If I ever have to take the axle out - it will take me 10 mins to cut that weld. 
All the hardware should be minimum grade 5








Have fun !
2009 R-Pod 172 Lifted 4"
2008 Nissan Xterra built up - too much to list
Computer Engineer with metal work as a hobby - or more - former NXRocks manufacturing
First time RV Camper - this better be good
Back to Top
Craneman View Drop Down
Senior Member
Senior Member
Avatar

Joined: 12 May 2013
Location: Tokeland,wa
Online Status: Offline
Posts: 387 		Direct Link To This Post Posted: 19 May 2014 at 11:25pm
Wow nice job, I should have went that route
      Moe
Jo and Gary, 2010-174,2011 F150

Jo and Gary
2010 174
2011 Ford 150



Back to Top
Hairy Podders View Drop Down
Senior Member
Senior Member
Avatar

Joined: 05 Mar 2014
Location: Northwest Ohio
Online Status: Offline
Posts: 217 		Direct Link To This Post Posted: 20 May 2014 at 7:04am
Looks very nice!
Our lift was included in the super low price, so that saved me the time.
Darryl, Julie & Lindsey
Cooper & Libby- Devoted Canines
2014 RP178
2006 Wrangler Unlimited Rubicon
Back to Top
fwunder View Drop Down
Senior Member
Senior Member
Avatar

Joined: 04 Oct 2013
Location: New Jersey
Online Status: Offline
Posts: 1676 		Direct Link To This Post Posted: 20 May 2014 at 8:07am
Very nicely done. How did you lift the trailer for installation?

fred
2014 RPod 178 => MyMods and Buying Habits
2008 4Runner Limited 4.0-liter V6
Yes, those are wild ponies dining on grass while dumping tanks!
Back to Top
NXRocks View Drop Down
Newbie
Newbie
Avatar

Joined: 27 Apr 2014
Location: Evergreen, CO
Online Status: Offline
Posts: 24 		Direct Link To This Post Posted: 20 May 2014 at 8:34am
On each side - lift the RV from under the axle, jack stands, take the wheel off, take the bolts off, lower the axle, put the new spacer, put the bolts, raise the axle, put the wheel, take the jack stands off, lower the axle.

One important thing - mark the alignment of the trailer frame and the axle. I used a masking tape
2009 R-Pod 172 Lifted 4"
2008 Nissan Xterra built up - too much to list
Computer Engineer with metal work as a hobby - or more - former NXRocks manufacturing
First time RV Camper - this better be good
Back to Top
techntrek View Drop Down
Admin Group - pHp
Admin Group - pHp
Avatar

Joined: 29 Jul 2009
Location: MD
Online Status: Offline
Posts: 9062 		Direct Link To This Post Posted: 20 May 2014 at 8:39am
Very nice looking.
Doug ~ '10 171 (2009-2015) ~ 2008 Salem ~ Pod instruction manual
Back to Top
gpod View Drop Down
Newbie
Newbie
Avatar

Joined: 23 May 2013
Location: Golden, CO
Online Status: Offline
Posts: 24 		Direct Link To This Post Posted: 02 Jul 2014 at 7:44pm
Where did you get the 2x4x3/16" risers that you used?  Were they pre-made and bought that way or did you have them custom-made somewhere?

Tnx!
Matt
Back to Top
Seanl View Drop Down
Senior Member
Senior Member
Avatar

Joined: 19 Sep 2011
Location: Fredericton NB
Online Status: Offline
Posts: 633 		Direct Link To This Post Posted: 03 Jul 2014 at 7:51am
Originally posted by gpod

Where did you get the 2x4x3/16" risers that you used?  Were they pre-made and bought that way or did you have them custom-made somewhere?

Tnx!

Looks like 2X4 Steel tubing you can get it an any steel supplier. 
Sean, 2011 Rpod RP-173,2009 Jeep Liberty Rocky Mountain Edition
Back to Top
NXRocks View Drop Down
Newbie
Newbie
Avatar

Joined: 27 Apr 2014
Location: Evergreen, CO
Online Status: Offline
Posts: 24 		Direct Link To This Post Posted: 03 Jul 2014 at 9:33am
As Sean said ... any steel supplier would have that - or get it online (while it will cost more) here for example: http://www.speedymetals.com/pc-4713-8224-4-x-2-x-188-wall-rectangular-steel-tubing.aspx
2009 R-Pod 172 Lifted 4"
2008 Nissan Xterra built up - too much to list
Computer Engineer with metal work as a hobby - or more - former NXRocks manufacturing
First time RV Camper - this better be good
Back to Top
gpod View Drop Down
Newbie
Newbie
Avatar

Joined: 23 May 2013
Location: Golden, CO
Online Status: Offline
Posts: 24 		Direct Link To This Post Posted: 03 Jul 2014 at 10:13am
Thanks for the info!  Looks like you're close by.  I'm in Golden.  Let me know if you ever want to meet up for a beer and compare rpod notes!
Matt
Back to Top
 Post Reply Post Reply Page  12>

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.64
Copyright ©2001-2009 Web Wiz