R-pod Owners Forum Homepage

This site is free to use.
Donations benefit a non-profit Girls Softball organization

Forum Home Forum Home > R-pod Discussion Forums > Podmods, Maintenance, Tips and Tricks
  New Posts New Posts RSS Feed: Don't ignore your bearings!
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

Topic ClosedDon't ignore your bearings!
 Post Reply Post Reply Page  12>
Author
Message
  Share Topic Share Topic  Topic Search Topic Search  Topic Options Topic Options
bhamster View Drop Down
Senior Member
Senior Member


Joined: 19 May 2011
Location: Washington
Online Status: Offline
Posts: 165 		Direct Link To This Post Topic: Don't ignore your bearings!
    Posted: 01 May 2013 at 1:02pm
With the camping season just kicking off I thought I'd share my experience in hopes that it might help someone else.

Our pod is just 2 years old with maybe 5k miles at most. I thought I'd repack the bearings before I took it out on the first trip of the year and it's a good thing I did. I was very surprised to find that water had made it into at least one of the bearings (I still have to do the other side).

The contamination was only on the outer bearing, so the cap must have failed. The inner bearing looked good. As you can see from the picture below it has obvious signs of rust and pitting.

Luckily my local NAPA had a kit with everything (bearings, races, cap & seals). I picked up a couple just in case the other side has the same issue.

So... if you think squirting a little grease through the zerk will make everything ready to go, think again. The grease itself showed no signs of contamination and both the washer and castle nut were fine. If I had just topped it off I never would have known. Make sure that you (or a trusted RV shop) take the bearings apart regularly and inspect and repack. I'll be doing this every year from now on.

I also discovered a few interesting things about the brakes that I'll share in another thread (after I take the pictures).
Back to Top
Goose View Drop Down
Senior Member
Senior Member
Avatar

Joined: 24 Sep 2010
Location: Arizona
Online Status: Offline
Posts: 672 		Direct Link To This Post Posted: 01 May 2013 at 3:59pm
   Great catch!!!!! This is why an inspection is more than worth the time and energy that you put into it. Goose
Mother Goose's Caboose..2011 RP171..07 Grand Cherokee
Back to Top
bhamster View Drop Down
Senior Member
Senior Member


Joined: 19 May 2011
Location: Washington
Online Status: Offline
Posts: 165 		Direct Link To This Post Posted: 01 May 2013 at 4:18pm
Originally posted by Goose

   Great catch!!!!! This is why an inspection is more than worth the time and energy that you put into it. Goose

Yep, I was so confident that it was going to be fine that I didn't even have spare bearings (just seals). It's worth it for the peace of mind and shouldn't take very long (unless they're rusted).
Back to Top
techntrek View Drop Down
Admin Group - pHp
Admin Group - pHp
Avatar

Joined: 29 Jul 2009
Location: MD
Online Status: Offline
Posts: 9062 		Direct Link To This Post Posted: 01 May 2013 at 8:17pm
Dang, glad you caught this.
Doug ~ '10 171 (2009-2015) ~ 2008 Salem ~ Pod instruction manual
Back to Top
bhamster View Drop Down
Senior Member
Senior Member


Joined: 19 May 2011
Location: Washington
Online Status: Offline
Posts: 165 		Direct Link To This Post Posted: 02 May 2013 at 2:02am
This afternoon I finished the job and interestingly the other side had contaminants on the inside bearing... so one of each kind of failure. Luckily the bearing itself was still usable, so I just needed to replace the seal and repack. I took some more pictures this time so you could see what it looked like. Here's what it looked like after taking the cap off (so far so good):



But once I pulled it off the spindle the dreaded rust color was obvious on the inner side:





Here's a side by side comparison of the caps (note the contamination was from the rubber plug, not the sides). I never even used the rubber plug:



Finally, here's the new seal I put in which seemed much higher quality than the OEM seals and went in much more easily (OEM on the left, new on the right):
Back to Top
Alex&Marie View Drop Down
Groupie
Groupie
Avatar

Joined: 25 Feb 2012
Location: Virginia
Online Status: Offline
Posts: 63 		Direct Link To This Post Posted: 02 May 2013 at 12:37pm
nice write up and great pictures! 

You have motivated me (for one) to tackle this - this weekend if the weather holds.  My mileage on the R-pod is probably on  the high side for a trailer that is only 14 months old: about 12,000 miles.

I'll let the group know what I find.

 
Alex and Marie
2012 R-pod 177
2006 Toyota Tundra
Back to Top
bhamster View Drop Down
Senior Member
Senior Member


Joined: 19 May 2011
Location: Washington
Online Status: Offline
Posts: 165 		Direct Link To This Post Posted: 02 May 2013 at 3:41pm
Originally posted by Alex&Marie

nice write up and great pictures! 

You have motivated me (for one) to tackle this - this weekend if the weather holds.  My mileage on the R-pod is probably on  the high side for a trailer that is only 14 months old: about 12,000 miles.

I'll let the group know what I find.

 

It's not hard at all... just messy. I used the majority of a "box of rags" switching between messy jobs and clean jobs (like taking pictures). Since everything was new for me this time each step took a few attempts due to new tools and unfamiliar procedures. By far, the hardest was removing the rusted race, but even that only took a few minutes once I found a nice-sized metal rod to bang it out with. The videos on etrailer are a great starting point.
Back to Top
Anthony Valenzano View Drop Down
Groupie
Groupie
Avatar

Joined: 09 Apr 2013
Location: Archbald Pa
Online Status: Offline
Posts: 44 		Direct Link To This Post Posted: 08 May 2013 at 1:32pm
I re-greased my bearings on my 2010 yesterday.  They were in very good shape.  No signs of rust at all.  I was surprised at how loose the castle nut was.  I wouldn't even say it was finger tight.  So I'm glad I looked at it.  There might have been enough slack to start some wobble.  Normally when I do bearings, I tighten them good with a wrench, at which point the wheel won't turn, then I back them off until the wheel spins freely, then back it off until I can insert the pin.  
Back to Top
bhamster View Drop Down
Senior Member
Senior Member


Joined: 19 May 2011
Location: Washington
Online Status: Offline
Posts: 165 		Direct Link To This Post Posted: 08 May 2013 at 1:45pm
That's another great point. Even if the bearings are in good shape, the preload needs to be adjusted as the bearings wear. Your procedure sounds similar to mine. I tightened as much as I could with a small crescent wrench while turning the wheel (this is really just to seat them properly and "smush" the grease). Then I backed off until the nut was loose, tighened again with my fingers until it catches, and then finished tightening with the wrench to the next point where I could insert the pin. So basically 1/4-turn or so past finger-tight. It should spin freely but not wobble.
Back to Top
Burt View Drop Down
Groupie
Groupie


Joined: 04 May 2012
Online Status: Offline
Posts: 62 		Direct Link To This Post Posted: 13 May 2013 at 12:20am
bamster:

Thanks for your post about the bearings.  I checked ours and to my delight, found that there were bearing buddies on them.  The grease was good as were the bearings and I learned about how to jack up the POD as well.

All good stuff and reminders.
Emoticons
Burt
Back to Top
 Post Reply Post Reply Page  12>

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.64
Copyright ©2001-2009 Web Wiz