Dewinterizing - R-pod Owners Forum

Author

Share Topic

Topic Search

Topic Options

Post Reply

Create New Topic

kp57george View Drop Down

Newbie

Joined: 13 Aug 2015
Location: Bay Village, OH
Online Status: Offline
Posts: 24

Topic: Dewinterizing
Posted: 01 May 2019 at 2:47pm

always can use help on this so I don't miss anything. Thanks

kp57george

Billy Bob

Senior Member

Joined: 11 Jun 2018
Location: Boulder City, N
Online Status: Offline
Posts: 103

Posted: 01 May 2019 at 6:09pm

I've never had to do that in southern nevada, but would think turn the bypass valves by the pump and water heater, hook up water and run both cold and hot water through every orfice to flush out the antifreeze.

Must be a lot of UTUBE video's on this.

2019 RPOD 190
2017 Chev Colorado 4 X 4
Yellow Lab and English Springer Spaniel

lostagain

Senior Member

Joined: 06 Sep 2016
Location: Quaker Hill, CT
Online Status: Offline
Posts: 2595

Posted: 01 May 2019 at 7:15pm

Check the archives on this topic and you should find something. Basically, you want to get the anti-freeze out of the system, i.e. the pink stuff. When you winterized you should have bypassed the water heater with two valves, in and out. Leave them alone until you clear out the lines. Hook up your city water and run it through all the lines - sink hot and cold, shower hot and cold and toilet. When you have no more pink stuff, you will have most of it out. Then turn off the city water.

You need to also get the anti-freeze out of the water pump and the little bit of tubing that connects it to the water system. Put some water in your fresh water tank and turn on the pump at the switch on the face of the galley cabinet. Turn on the cold water and run it with the pump until it is clear. You may want to turn on the hot side too, just in case some anti-freeze got in that line. Once all the pink is gone, turn off the pump.

Once you have all the anti-freeze out of the pipes, then you need to put the hot water heater back into service. First, make sure you've replaced your anode rod using plumbers tape to seal it. Tighten it very snug with a socket wrench. Once the anode is secure, go back and open your bypass valves so the handles are in line with the pipes. Turn your city water back on and turn on the hot water in the galley and shower to let the air out of the water heater tank. Once you have free flowing (no air) water coming out, then you can turn off the hot water valves in the shower and sink.

You're done. Be sure to check your electric water heater switches to be sure they are both off. One is on the outside of the water heater in the left lower quadrant, under some gas lines. The other is the breaker for 120vac water heater circuit. The water heater switch on the galley cabinet is only for gas operation. Hope this helps.

Never leave footprints behind.
Fred & Maria Kearney
Sonoma 167RB
Our Pod 172
2019 Ford F-150 4x4 2.7 EcoBoost

kp57george View Drop Down

Newbie

Joined: 13 Aug 2015
Location: Bay Village, OH
Online Status: Offline
Posts: 24

Posted: 01 May 2019 at 7:18pm

The problem I still have is getting the water pump to run the water into the faucets. The winterizing solutions have been flushed. The water tank has been filled. I hear the pumpchurning, Air comes through, no water. I changed the anode. Hot water is in the hot water tank. I just must have some lines not open.

kp57george

kp57george View Drop Down

Newbie

Joined: 13 Aug 2015
Location: Bay Village, OH
Online Status: Offline
Posts: 24

Posted: 01 May 2019 at 7:22pm

Thanks. I will hit it all agian tomorrow, Appreciate your help. George

kp57george

StephenH

podders Helping podders - pHp

Joined: 29 Nov 2015
Location: Wake Forest, NC
Online Status: Offline
Posts: 6417

Posted: 02 May 2019 at 10:15pm

Check the valve that connects to the stub tube that is used for putting the pink stuff into the system. If all you are pumping is air, then it is very likely that the valve is set still to draw from an antifreeze bottle and not the water tank.I've had this happen to me also. Now I change it back as soon as I finish pumping antifreeze so I won't forget the following spring.

StephenH
Happy is the man that findeth wisdom,...

ouR escaPOD mods
Former RPod 179
Current Cherokee Grey Wolf 24 JS

Ted

Newbie

Joined: 08 Oct 2018
Location: Colorado
Online Status: Offline
Posts: 8

Posted: 20 Jun 2019 at 2:30pm

Thank you StephenH. Problem solved! The valve was still set to draw antifreeze. I'm now ready for the road - - - I hope.

Ted

Author	Message Share Topic Printable Version Google Delicious Digg StumbleUpon Windows Live Yahoo Bookmarks reddit Facebook MySpace Newsvine Furl Topic Search Topic Options Post Reply Create New Topic
kp57george Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 13 Aug 2015 Location: Bay Village, OH Online Status: Offline Posts: 24	Topic: Dewinterizing Posted: 01 May 2019 at 2:47pm
	always can use help on this so I don't miss anything. Thanks
	kp57george

Billy Bob Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 11 Jun 2018 Location: Boulder City, N Online Status: Offline Posts: 103	Posted: 01 May 2019 at 6:09pm
	I've never had to do that in southern nevada, but would think turn the bypass valves by the pump and water heater, hook up water and run both cold and hot water through every orfice to flush out the antifreeze. Must be a lot of UTUBE video's on this.
	2019 RPOD 190 2017 Chev Colorado 4 X 4 Yellow Lab and English Springer Spaniel

lostagain Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 06 Sep 2016 Location: Quaker Hill, CT Online Status: Offline Posts: 2595	Posted: 01 May 2019 at 7:15pm
	Check the archives on this topic and you should find something. Basically, you want to get the anti-freeze out of the system, i.e. the pink stuff. When you winterized you should have bypassed the water heater with two valves, in and out. Leave them alone until you clear out the lines. Hook up your city water and run it through all the lines - sink hot and cold, shower hot and cold and toilet. When you have no more pink stuff, you will have most of it out. Then turn off the city water. You need to also get the anti-freeze out of the water pump and the little bit of tubing that connects it to the water system. Put some water in your fresh water tank and turn on the pump at the switch on the face of the galley cabinet. Turn on the cold water and run it with the pump until it is clear. You may want to turn on the hot side too, just in case some anti-freeze got in that line. Once all the pink is gone, turn off the pump. Once you have all the anti-freeze out of the pipes, then you need to put the hot water heater back into service. First, make sure you've replaced your anode rod using plumbers tape to seal it. Tighten it very snug with a socket wrench. Once the anode is secure, go back and open your bypass valves so the handles are in line with the pipes. Turn your city water back on and turn on the hot water in the galley and shower to let the air out of the water heater tank. Once you have free flowing (no air) water coming out, then you can turn off the hot water valves in the shower and sink. You're done. Be sure to check your electric water heater switches to be sure they are both off. One is on the outside of the water heater in the left lower quadrant, under some gas lines. The other is the breaker for 120vac water heater circuit. The water heater switch on the galley cabinet is only for gas operation. Hope this helps.
	Never leave footprints behind. Fred & Maria Kearney Sonoma 167RB Our Pod 172 2019 Ford F-150 4x4 2.7 EcoBoost

kp57george Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 13 Aug 2015 Location: Bay Village, OH Online Status: Offline Posts: 24	Posted: 01 May 2019 at 7:18pm
	The problem I still have is getting the water pump to run the water into the faucets. The winterizing solutions have been flushed. The water tank has been filled. I hear the pumpchurning, Air comes through, no water. I changed the anode. Hot water is in the hot water tank. I just must have some lines not open.
	kp57george

kp57george Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 13 Aug 2015 Location: Bay Village, OH Online Status: Offline Posts: 24	Posted: 01 May 2019 at 7:22pm
	Thanks. I will hit it all agian tomorrow, Appreciate your help. George
	kp57george

StephenH Members Profile Send Private Message Find Members Posts Add to Buddy List podders Helping podders - pHp Joined: 29 Nov 2015 Location: Wake Forest, NC Online Status: Offline Posts: 6417	Posted: 02 May 2019 at 10:15pm
	Check the valve that connects to the stub tube that is used for putting the pink stuff into the system. If all you are pumping is air, then it is very likely that the valve is set still to draw from an antifreeze bottle and not the water tank.I've had this happen to me also. Now I change it back as soon as I finish pumping antifreeze so I won't forget the following spring.
	StephenH Happy is the man that findeth wisdom,... ouR escaPOD mods Former RPod 179 Current Cherokee Grey Wolf 24 JS

Ted Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 08 Oct 2018 Location: Colorado Online Status: Offline Posts: 8	Posted: 20 Jun 2019 at 2:30pm
	Thank you StephenH. Problem solved! The valve was still set to draw antifreeze. I'm now ready for the road - - - I hope. Ted